Technical Specifications
Rev 2/18/2010
Description: rubbRe’s™ feel is unique in the industry, joining the durability of rubber to the hand of a finely made non-woven material. It is suitable for many uses and is available in various gauges and colors.
Compound: Proprietary; made from at least 30% crumb rubber from used car tires taken from US land fills.
Colors: Standard – Black; other colors available including: Blue, Grey, and Green
Availability: Delivered as rolled goods
Origin: Made in the USA
|
Properties
|
Specifications
|
|
Minimum Tensile:
|
1650.5 PSI (.030), 1830.5 PSI (.067)
ASTM-D412-97 Method A, Die C
|
|
Tear Strength:
|
223 lbf/in ASTM-D624C
|
|
Temperature Range:
|
- 40°F to 200°F
|
|
Width:
|
60 inches
|
|
Gauge
|
Weight
|
Roll Length
|
Gauge Tolerance
|
|
0.30 in
|
22.25 oz/y2
|
20 linear yd
|
+/- 0.005 in
|
|
0.67 in
|
54.00 oz/y2
|
10 linear yd
|
+/- 0.075 in
|
|
Shore A Hardness:
|
45
|
|
Elongation:
|
435.50%, ASTM-D412-97 Method A, Die C
|
|
Specific Gravity:
|
1.17
|
|
Staining Resistance
|
No visible migration
|
|
Ozone Resistance:
|
100%, ASTM-D1171
|
|
Flammability:
|
1
|
|
Flexibility:
|
Excellent flexibility and good elasticity.
|
|
Density:
|
1.15 g/cc |
***Except where noted, data are presented as typical values and should not be construed as specification limits***.
|
Lab Testing Results
|
|
Test
|
Result
|
|
ASTM D5034-95 (2001) / ASTM D3597-02 Breaking Strength and Elongation of Textile Fabrics (Grab Test) [.030" rubbRe™]
|
Avg. of Warp: 57
Avg. of Fill: 50
|
|
ASTM D3511-05 Pilling Resistance and Other Related Surface Changes of Textile Fabrics: Brush Pilling Tester [.030" rubbRe™]
|
5.0 – No Pilling
|
|
Colorfastness to Light AATCC Test Method 16-2004, Option 3 [.030" rubbRe™]
|
Class 5.0 – 40 Hours
|
|
Colorfastness to Wet & Dry Crocking AATCC 8-2001 [.030" rubbRe™]
|
Dry Crocking: Class 4.0
Wet Crocking: Class 4.5
|
|
California Technical Bulletin 117, Section E (CPSC 16 CFR 1610 – CS 191-53) Upholstery Fabrics [.030" rubbRe™]
|
Complies
|
|
ASTM D4157-02 Abrasion Resistance of Textile Fabrics (Oscillatory Cylinder Method) [.030" rubbRe™]
|
TBD 15,000 Double Rubs
|
|
U.S. 21 CFR FDA 177.2600 – FDA Food Simulating Solvent Extraction (Rubber – Silicone)
|
Complies
|
|
ASTM E2179-09 Measurement of Effectiveness of Floor Coverings in Reducing Impact Sound Transmission Through Concrete Floors [.067" rubbRe™]
|
ΔIIC 20
|
|
ASTM D 1894-06 Coefficient of Friction [.030" rubbRe™]
|
2.45
|
|
| ASTM D 6866 Biobased Content |
76% |
|
| Additional Information |
| Recommended Adhesive |
3M Scotch-Weld 4799 Industrial Adhesive |
| Stitching Info |
Use a standard needle, not a diamond tip. Fewer stitches are better as too many stitches will puncture the material; 10-12 stitches/inch should provide sufficent strength. |
The data contained herein are subject to revision without notice. Vulcana®, LLC assumes no responsibility for testing and process variables. All measurements are approximate and subject to change based upon other factors. The material properties provided in this sheet represent comparative and projected product performance, and do not constitute design allowables or affirmative representations. Natural variations in these properties occur as a consequence of the manufacturing process. Any use of Vulcana® products should be subjected to acceptance tests, by the user, appropriate for the application. Because of the unique nature of the material, alternative test methods or greater test material size may be necessary for accurate results.The data is furnished without liability to Vulcana® or its agents and does not constitute a warranty or representation with respect to the material or its use.
© 2008 Vulcana, LLC. All rights reserved worldwide. Vulcana® is a registered trademark of Vulcana, LLC. rubbRe™ and fuzun™ are trademarks of Vulcana, LLC. Vulcana, LLC assumes no responsibility for any errors in this document. Vulcana, LLC reserves the right, without notice, to make changes in product design or specifications.